Functional Description

The xSil268B is designed to connect an IDE/ATAPI device or Flash media to USB. It contains the following:

• 100-pin 16mm x 16mm QFP package

• Single chip with integrated USB 2.0 PHY

• Serial EEPROM port

• Supports up to 25 types of media. (Application notes available.)

• IDE/ ATAPI/ MMC™/ SD™/ Memory Stick™ / SmartMedia™/ xD™/ CF™ interface

• Supports for High Speed operation of MMC/SD, Memory Stick and SmartMedia Cards

• Support for MS PRO™, HS (4-bit mode)

• Supports SmartMedia ROM, Memory Stick ROM media

• Supports for xD media, up to 2GB.

• Supports for xD M series & H series media

• Supports On-board NAND as a storage device

• Firmware enhancements can be stored on On-board NAND when populated

• Serial port

• Two General Purpose Timers

• Watchdog Timer

• 16 bit Processor

• Internal RAM for supporting enhancements

• ROM with BIOS and Application code.

• Programmable Read and Write widths

• Optimum hardware controlled transfer for speed and scalability

• Built in 128-bit AES Encryption (real time) for in-bound and out-bound data

MultiMediaCards/ Secure Digital Cards

• Supports SD Card High Speed mode (48MHz clock)

• Supports miniSD, MicroSD, TransFlash

• Supports MMC media with 1-bit, 4-bit and 8-bit modes (48MHz clock)

• Supports MMCPlus, MMC Micro, RS MMC media

CompactFlash / Microdrive

• Supports CompactFlash UDMA Modes 0..4, MDMA Modes 0..2, PIO Modes 0..6

• Supports IDE / ATAPI devices up to PIO Mode 4

• Supports IBM, Seagate, Hitachi and MagicStor Hard disk based CF media

xD/ SmartMedia/ NAND flash

• Supports SmartMedia ROM, Memory Stick ROM media

• Supports for xD media, up to 2GB.

• Supports for xD M series media - V1.2 xD Picture Card Specification compliant.

• Supports for xD H series media

• Supports On-board NAND as a storage device, 8-bit and 16-bit

• 1-bit error correction and 2-bit error detection for SM and xD based on ECC.

• FEC Error detection and Correction, which can correct up to 4-bytes of error per sector with Parity data included.

• Firmware enhancements can be stored on On-board NAND when populated. With this enhancement the first NAND block is not require to be good.

Memory Stick/ Memory Stick PRO

• Supports Memory Stick Classic and Memory Stick High Speed

• Supports MS PRO™, HS (4-bit mode)

• Supports MS Duo, MS PRO Duo

• Support for Memory Stick ROM

Packaging

The xSil268B is a 100-pin QFP package.

USB Engine

The xSil268B meets the Universal Serial Bus (USB) specification V2.0 and V1.1.

Serial EEPROM Port

The xSil268B provides a serial interface to access external EEPROM's. The interface is implemented using General Purpose I/O signals and can support a variety of serial EEPROM formats.

IDE/ ATAPI

The xSil268B processor can be designed to interface to an IDE or ATAPI device. It supports PIO mode of data transfer.

Support for CF, MMC/ SD, Memory Stick, xD and SmartMedia Cards

The MultiMediaCard (MMC), Secure Digital Card (SD Card) and Memory Stick are serial access devices. They also require in-bound / out-bound data to be appended with CRC information. The xSil268B processor provides support in hardware to generate the CRC and to convert Serial to Parallel and Parallel to Serial bit streams. A programmable clock speed is provided to set the clock speed based on the media's capabilities. The xSil268B also provides Hardware ECC generation and checking for SmartMedia and XD. CF cards may be connected directly as an IDE device.

Serial port

Supports 7200 to 115.2K baud. It can be used as a debug port to communicate with V3 debugger and to load the monitor program.

General Purpose Timers

Two general-purpose timers, Timer0 and Timer1 are provided to allow firmware programmers to keep track of timeouts as well as to generate delays.

Watchdog Timer

A Watchdog Timer is provided to enable catastrophic events to interrupt the processor. The Watchdog Timer overflow causes an internal processor reset. The Processor can read the WT bit after exiting reset to determine if the WT bit is set. If it is set, a watchdog timeout occurred. The timeout is selectable to any of the following values: 2 second, 8 seconds, 16 seconds or 32 seconds.

xSil 268B Processor

The xSil 268B Processor has a built-in 16-bit processor along with a BIOS ROM. The processor operates with a specialized instruction set optimized for Mass Storage applications and USB transaction processing. The startup code for the 16-bit processor resides in a masked ROM.

RAM Interface

The xSil268B chip comes with Internal RAM that can be used to enhance the firmware resident in the ROM.

Masked ROM

The Masked ROM consists of the xSil268B processor start-up code and the functions listed below:

• Power On Initialization

• USB packet transaction management

• USB Power Management (S0..S3 modes)

• USB Enumeration Management

• API support for USB transactions, EEPROM Interface, Memory Management etc.

• Built-in Library functions for IDE/ ATAPI and Flash devices

The firmware is easily extended / expanded by using External Serial EEPROM. The BIOS provides several services to facilitate this expansion code. At boot-up time, the scan services of the BIOS search for the expansion signature in the Serial EEPROM as well as via the UART and USB. For more information, refer to Applications section of this manual.

The BIOS API functions are designed as Software Interrupts, making it easy for enhancements. Any Interrupt can be enhanced / modified by inserting the user defined function in the interrupt placeholder. When this interrupt is called by the BIOS, the user defined function is called first to enhance the behavior before passing it on to the standard BIOS function's call or return without passing it on.

Programmable Read and Write cycles

The external cycles to flash using the D[15:0], and SM[7:0] bus are software configurable.